SonotaCo.JP
SonotaCo Network Japan Forum
SonotaCo.JP Forum Index
homeTop Page  FAQFAQ   検索検索   メンバーリストメンバーリスト   ユーザーグループユーザーグループ   登録する登録する 
 プロフィールプロフィール   プライベートメッセージをチェックするプライベートメッセージをチェックする   ログインログイン 

UFO Analyzer v2 quickstart guide

 
新しいトピックを投稿   トピックに返信    SonotaCo.JP Forum Index -> UFOCapture BBS in English
前のトピックを表示 :: 次のトピックを表示  
投稿者 メッセージ
Robert J Cobain



登録日: 2006.04.25
記事: 79

記事日時: Mon Apr 02, 2007 11:06 pm    記事の件名: UFO Analyzer v2 quickstart guide 引用付きで返信

Hi all,

Here are some quickly typed up instructions to get started using UA2,

How to use UA2

Open and Prepare UFOCapture main program

Input tab
Enable AVI codec
Enable Scintillation mask


Operation tab

Enable Logging,
Enable Map BMP

Profile tab
set up accordingly

Open and Prepare UfoAnalyzer2
ground map, http://sonotaco.com/soft/e_index.html
Load ground map tab


Main tab,

clip dir add, select directory of captured meteors
make sure asterisk, otherwise click to enable dir
make sure date all
press, read dir

select a clip, with plenty of stars
choose mask editor tab
choose profile/analyze tab
input approximate details profile/analyze tab
select correct timezone tz, +1hr = 3600 profile/analyze tab
bst = 3600 profile/analyze tab
tick intlc if video is interlaced, usually true profile/analyze tab
tick bbf if using DV video like canopus profile/analyze tab
tick all boxes for fovh, yx, k2,k3,dy,dx,k4 profile/analyze tab
make sure mg is ticked on the mask editor tab
this means they will be considered when calculating the best position
Use the move arrows along with rot parameter to get an approx match
when you see they correct stars in yellow, near the stars in the scintillation blue, press link mask editor tab
then manual link mask editor tab
then left select the yellow star, hold down the left mouse button as you drag the line
to the corresponding star in blue, let go of the left mouse button when in the center of the blue main window
repeat for as many stars as possible
click finish link mask editor tab
click adj pos all profile/analyze tab
wait while UA2 calculates
when finished click auto link mask editor tab
then click adj pos all again profile/analyze tab
then click mag, this will calibrate magnitudes profile/analyze tab
hopefully all yellow stars will now be inside the blue scintillation mask points
some blue 'stars' will be hot pixels so ignore them
click save P and save this profile profile/analyze tab
hit A to analyze profile/analyze tab
close down UA2 and open it up again, so that it 'remembers' this profile
if UA2 'forgets this profile, you will need to click read P and read the profile you saved
for each clip press A to analyze or if all clips will have same profile , click analyze all main tab
If you click 'analyze' UA2 will not recalibrate magnitude and position profile/analyze tab
If you click 'A' then calibration occurs for position and magnitude
Clicking analyze all is the same as clicking 'A' for each clip profile/analyze tab

Let me know if you have any problems, Robert.
トップに戻る
ユーザーのプロフィールを表示  
特定期間内の記事を表示:   
新しいトピックを投稿   トピックに返信    SonotaCo.JP Forum Index -> UFOCapture BBS in English All times are GMT + 9 Hours
Page 1 of 1

 
移動先:  
新規投稿: 不可
返信投稿: 不可
記事編集: 不可
記事削除: 不可
投票参加: 不可
このフォーラムで添付ファイルを投稿 できません
このフォーラムでファイルをダウンロード できます


Powered by phpBB © 2001, 2005 phpBB Group
Copyright ©2004 SonotaCo Network. All Rights Reserved.