前のトピックを表示 :: 次のトピックを表示 |
投稿者 |
メッセージ |
geosweiningen
登録日: 2013.10.31 記事: 39 所在地: Val Terbi, Switzerland
|
日時: Wed Apr 20, 2016 9:07 am 記事の件名: Pulsating noise and permanent recording in UFOCaptureHD |
|
|
Dear all,
I made this night the first time observations with the ilce-7sm2, blackmagic intensity shuttle and UFOCaptureHD. It seems like I have a problem with some pulsating noise.
When I start Detection everything works fine. After a while (about 1 minute), the Detect Size Level starts pulsating. It’s getting on a certain level and falls back to 0, goes to a higher level and falls back to 0, goes to an even higher level and falls back to 0, and so on. After a short time, UFOCaptureHD starts to record permanently.
I used the Scintillation Mask and have set the SMlevel as high as I could. No effect.
If I activate the “ignore blackout” (could not find out for what this function is), than the noise is gone, but unfortunately the signal too. Mask the black border of the frame in the Detect Area Editor also has no effect.
Any suggestion what I could do?
Best Regards,
Roger
_________________ Val Terbi, Switzerland
http://www.ogvt.org |
|
トップに戻る |
|
|
SonotaCo Site Admin
登録日: 2004.08.07 記事: 12669 所在地: 139.67E 35.65N
|
日時: Thu Apr 21, 2016 7:58 am 記事の件名: |
|
|
There are some possibilities.
Please show me below
1. snapshot image of your Input sheet. and Live sheet Detect Size setting.
2. ploblem sample clip file, M*P.jpg and zipped M*M.bmp) images
( you can stop recording by increasing the Detect Size or DLratio)
The most probale cause may be the noise or faint air plane detecting.
If those, you can see the reason( triggering pixel) on the R channel of M*M.bmp
|
|
トップに戻る |
|
|
geosweiningen
登録日: 2013.10.31 記事: 39 所在地: Val Terbi, Switzerland
|
日時: Sun Apr 24, 2016 4:52 am 記事の件名: |
|
|
Hi Sonotaco
Thank you for your support and sorry for the delay in responding. In the meantime, I bring it to work. I reduced the ISO value at the Camera and after that it worked properly.
Here is the Input Screen:
And the Live Sheet Detect Size setting
It’s funny, because I have the same problem with one of my WATEC Systems that I run.
I use there a VC006AUSB Grabber from ems imaging: http://www.ems-imaging.com/index.php/usb-3-0-video-capture/6-ch-a-v-video-capture and operate 4 Watecs.
If I let the Grabber Setting at Standard, I have a permanent detection:
Only when I set the Deinterlace settings at ?Motion Adaptive“ then It works.
The result is then an deinterlaced Capture which seems not to bee ok.
The other Server has no Problems. There I use three cheap Basetec USB Grabber:
What value for increasing the Detect Size or DLratio settings are usable to detect Meteors and TLE? I think I cannot set them too high.
Best Regards
Roger
_________________ Val Terbi, Switzerland
http://www.ogvt.org |
|
トップに戻る |
|
|
SonotaCo Site Admin
登録日: 2004.08.07 記事: 12669 所在地: 139.67E 35.65N
|
日時: Sun Apr 24, 2016 7:52 pm 記事の件名: Setting samples |
|
|
Here are sampls for each resolution of my station.
These are not most sensitive, but aiming stable meteor observation.
You can set more sesitive, but there may be many unwanted clips or long clips. It depends on the purpose.
Anyway, S/N of video source is very important for motion detection. It should be above around 30db.
説明: |
|
ファイルサイズ: |
369.9 KB |
閲覧数: |
6886 回 |
|
説明: |
|
ファイルサイズ: |
475.32 KB |
閲覧数: |
6886 回 |
|
説明: |
|
ファイルサイズ: |
239.6 KB |
閲覧数: |
6886 回 |
|
|
|
トップに戻る |
|
|
geosweiningen
登録日: 2013.10.31 記事: 39 所在地: Val Terbi, Switzerland
|
日時: Mon Apr 25, 2016 6:35 am 記事の件名: |
|
|
Dear SonotaCo
I think it was the MinL-N and MinDL values. They were obviously set to close. I'll try it now with the new settings.
Thank you very much for your very valuable input!
Best Regards,
Roger
_________________ Val Terbi, Switzerland
http://www.ogvt.org |
|
トップに戻る |
|
|
|